Exactly How To Install A Bath Tub (For Novices).
Visit WebsiteWhat are your ideas on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Setting up a bath tub isn't exactly rocket science, yet it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult project. If the old tub is easily accessible, the project can move speedily; if you need to open up a wall to eliminate the old bathtub and also position the new tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to leave the old tub as well as set in the brand-new one. See to it you have qualified on your own for the job and fit trying it. As opposed to working with a contractor to take over a halfway-completed task, it is far better to consider employing one before you begin. Possibilities are you might need an expert plumber to make tube connections.
This write-up will aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and don't require to alter the setup of your previous water pipes.
Your tools as well as product list should comprise the following:
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you ought to do is detach the water supply. After doing so, switch on the taps to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be quite problematic as a result of the limited accessibility that is commonly the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipes to the taps. Have a fabric ready for the remaining water that will certainly originate from the pipelines. Once the supply pipelines have been gotten rid of, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to quit the single faucets from turning throughout this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing substance.
Prior to carrying on to fit the new faucets, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washers remain in location in between the tap and the sink. Safeguard the tap in position with the maker provided backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by using corrugated copper piping or with typical tap ports. The previous type needs to be linked to the tap finishes first, tightening only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Bath tub
Using both wood boards under its feet, place the bath tub in the called for position. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to guarantee that the bath tub is leveled all round. This can be accomplished by examining the level and also adjusting the feet on the bathtub till the spirit level checks out degree.
To install taps, fit all-time low of the outermost flexible tap adapter to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Activate the supply of water and inspect all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub and also examine the overflow outlet as well as the regular electrical outlet for leaks.
Finally, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bath tub should wait until the tub has been utilized at the very least when as this will settle it right into its last position.
Getting ready for the Setup
To start with, the sustaining frame provided with the bath ought to be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is necessary to see to it that if the faucet includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets system to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you make use of all of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now prepare to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a stiff seal, causing the water to pass through the wall surface between the bathroom as well as the tiling, leading to difficulties with moisture as well as feasible leakages to the ceiling below.
You can choose from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and also cartridges, and can sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Remember to constantly fill the bathtub with water prior to sealing, to permit the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not consider this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise conveniently available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy more info about Tools You Need to Install a New Bathtub ? Write a short review further down. We'd be interested to see your insights about this page. In hopes to see you back again later on. Liked our piece of writing? Please share it. Help somebody else check it out. We truly appreciate reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Or Book Technician Here